While the directions leave a bit to be desired, I think this is a great value for the money. I also like this brand in general, I've bought a few other cupboards and such for my kitchen, and it's nice to have things that matchI do not mind assembling items, I actually enjoy it. However, this was such a pain to assemble! Two parts were mislabeled (part 5 was labeled as part 8 and part 9 was labeled as part 6). The instructions told you to to put part L on part 12... part L didn't exist, it was labeled as part c. The instructions referred to the screws as d2 and d3 when all these screws were all in a bag labeled d... plus, the instructions had me put the roller tracks on backwards- I had to take those off and redo them.Finally, I got it all put together and there's a gap in the drawer (even after fixing the tracks). No matter how I put the drawer in, there's a gap. It's very frustrating.Despite the gap, the piece as a whole seems pretty sturdy and it's still going to work for what I wanted (it's a microwave cart, but I'm using it as my cricut cart- my cricut fits perfectly). I was so concerned about making sure the item was wide enough, that I failed to notice how tall this thing was ?.The instructions state you need a hammer, a Philips head screw driver, and a tape measure. It never told me to measure anything, so I didn't use my tape measure. I'd like to recommend getting a lint roller because the Styrofoam pieces were everywhere once I opened that box! It was a mess! Unfortunately, I didn't have a lint roller and had to use tape to pick up the static pieces.Anyone who has experienced the kits from companies like Ikea will be familiar with the methodology of putting this cart together. However, this kit seems not to have been manufactured with the same care and precision of other manufacturers.For example:The countersunk holes into which fasteners are to go vary in depth and diameter. Some fasteners tighten to a depth level with the surface, others are left protruding.When they are not fully level, the decorative caps supplied look silly floating above the surface.The pre-drilled holes into which the fasteners are threaded, in some cases, seemed to be on the wide side and did not provide adequate grip in the particle board to fully tighten the fasteners.The handles for the drawer and cabinet doors are cheap plastic and easily broken under normal useThe screws to mount the handles are an incorrect length. Some allowing only two or three threads to grip the plastic handles through the front of the drawer or door.The front and back of the drawer bottom is held in place (vertically) only by nails. This seems like only a matter of time that normal use of the drawer will lead it to fail.This cart will suffice for my intended purpose, but I would have rather spent a bit more and got better quality.This is made out of particle board - the packing was terrible - there was a gouge out of one of the sides and one handle had a fairly deep scratch in it. The back is just a piece of cardboard! Not what I was expecting at all.The instructions were trash. But figured it out and it is pretty nice. Little over priced for what I endured and gotIf you are looking for a microwave cart that is cheap and can only handle a light weight small microwave and you are not looking for drawers that can handle somewhat heavy items. This cart is for you. I bought two of these and put them together in about four hours. The assembly was somewhat easy, there were only a couple of unclear assembly issues. These issues caused me to really think about, what a part was for and how I should place them. Luckily I guess right. It was easy for me to see how some people may have put certain parts in, the wrong way. The two major problems with this item, are both cosmetic in nature. Both carts had noticeable defects in the finish, ranging from faded faux wood finish to chip and peeling faux wood finish. Combine that with the fact that all of the side panel screws do not become flush with the side panels without some serious effort with a very small tool. If you do not put the effort in, you probably will leave the screw heads visible, because using the head covers will leave them sticking out away from the panels quite noticeably. In short, this product will not enhance anything in your kitchen unless you have next to nothing. It will provide some useful utility, if your expectations are not very high.I have assembled A LOT of furniture in my time and you know what gets me? That big bag of screws and other parts all jumbled together. Do I use this screw or the almost identical one that is a cm longer? Is that a picture of the 1 inch dowel or the 2 inch? I can't tell from the picture. Well this product was refreshing in that each set of screws, etc came in their individually wrapped AND LABELLED bags. The holes were all perfectly drilled and everything was where it shoukd be. You could not mess this up if you tried.Word of advice when putting in the doors. Take out the frame screws for the piece above where the magnets attach. It will be much easier to get the door in.Now we just have to see if it lastsNot as expectedMuy baja calidad relación costo beneficio muy malaManquait des numéro sur trois pièces